(ENG) [4DDM] Live View

Live View Setting(Single Mode)

In Live View Setting (Single Mode), you can set camera properties and gimbal position. You can connect / disconnect all cameras before 4DPD operation, and set detailed settings for specific cameras.

Open

•  Monitoring Source: Load monitor video source from Direct Camera or Presd (* Direct Camera is available when not recording, and Presd source is available when 4DPD is recording).

• Display type: Simple one-camera Live View Mode (Default), two-camera Comparison Mode (* However, Comparison Mode can take up a lot of load when used simultaneously during video production, so refrain from using it at the same time.)

• Connect All: When clicked, the camera screen is executed live (※ Waiting time is required to turn on the camera after clicking once).

• Draw: Used to scale the reference bar, drag to create a bar, drag the red dot to adjust the position, and drag the blue line to move it.

• Clear: Delete the bar

• Refresh: Refresh the camera video connection

• Guide Line Color: Change the color of the guidelines displayed in Live View

• Rotate: Click the "Rotate" button to rotate the video 180º, and you can create a rotated video without any calibration data.

Live View Setting(Comparison Mode)

Live View Setting (Comparison Mode) allows you to set camera properties, gimbal position, and connect / disconnect the camera to compare two cameras and make detailed settings.

Open

• Comparison Mode: Compare the video of two CAMs and set the properties and gimbal Live View Mode: Compare the video of two CAMs and set the properties and gimbal.

• Camera Selection (1), (2) : Use the drop-down to select each camera for comparison.

• Refresh : Refresh the camera video connection

• Live View Comparison Video: Video to compare with the left Live View target

• Live View applied image: Image to which the right Live View Property and Gimbal setting values are applied.

• Scope comparison: Check the scope status of the image color under the Live View image

Property

Property allows you to set detailed properties of the camera connected to the 4DDM.

• Exposure

  • ISO: Adjust the light sensitivity setting

  • Aperture: Control the amount of light entering the aperture

  • Shutter Speed: Set the shutter speed

  • -/+ 1EV : TBD

•   Color

  • White Balance : TBD

  • Temperature: Adjust to modify the color of light

  • RGB Balance Adjustment: Set the RGB color of the video

  • Saturation: Set the color saturation of the image

  • Contrast: Set the brightness of the image

  • Hue: Video color settings

• Lens

  • Zoom: Lens zoom setting

  • Focus: Set lens focus (AUTO: Focus automatically)

•   Scope

  • Parade: Video color correction value monitoring mode

  • Waveform: Waveform monitoring mode for image color correction values

  • Overlay: Monitoring mode for overlaying image color correction values

•   Memory / Revert

  • Memory : Temporarily stores the current Property value and saves it by clicking “Save.”

  • Revert : Return to the property value at the time of clicking Memory

Gimbal

Gimbal allows you to customize the properties of the Gimbal device attached to your camera. These settings are only used when you install and use Gimbal.

• Gimbal Control

  • WakeUp All: Activate all gimbals

  • Sleep All: Deactivate all gimbals

  • All: Select all registered gimbal devices to apply option (WakeUp All, Sleep All)

•  Gimbal Balance

  • Get Position : Retrieve the current Gimbal position

  • Set All / Stop All : Roll/Tilt/Pan simultaneously to move/stop coordinates

  • Speed : Adjust the movement speed of the gimbal

  • Roll/Tilt/Pan : TBD

• Gimbal Controller

  • [Continuous], [OneStep]: Option to select whether to move the gimbal continuously or in a single step using the buttons.

  • [Step]: When using the OneStep Gimbal movement option, the interval of movement per click.

  • Roll/Tilt/Pan: After adjusting the coordinates, click the direction display to move to the set coordinates.

• Lens

  • Zoom: Enter directly or adjust the bar to set a value > Save as [Set]

  • Focus: Enter directly or adjust the bar to set the value > Save as [Set].

  • Set: Set the selected value

  • Auto: Set auto focus

• Preset

  • Preset List: List of available presets for saving Gimbal settings, click to set after

  • Save: Save the current Gimbal settings to the selected Preset List

  • Load: Load Preset settings from a specific folder (save to 1-8)

  • Apply to Gimbal : Apply the current Gimbal setting to the clicked Preset

  • Set : Save the current Gimbal Position to the selected Preset number

  • Move: Move the selected Preset number Position value

Step of Gimbal Preset Setting

• Step 1. Activate the gimbal WakeUP All

• Step 2. Move the gimbal using the gimbal controller

• Step 3. Set the zoom and focus of Lens

• Step 4. Click the desired Preset_Number and click Save Preset

  • (If you want to move to the desired Preset_Number setting value, click Move after clicking Preset_Number)