This is the most important tab for shooting video, as it allows you to zoom in and out of the camera, focus, and set properties. Live View is the live camera view where you can set the camera's properties and gimbal position.
Live View Setting(Single Mode)
In Live View Setting (Single Mode), you can set camera properties and gimbal position. You can connect / disconnect all cameras before 4DPD operation, and set detailed settings for specific cameras.
Monitoring Source: Load monitor video source from Direct Camera or Presd (* Direct Camera is available when not recording, and Presd source is available when 4DPD is recording).
Display type: Simple one-camera Live View Mode (Default), two-camera Comparison Mode (* However, Comparison Mode can take up a lot of load when used simultaneously during video production, so refrain from using it at the same time.)
Connect All: When clicked, the camera screen is executed live (※ Waiting time is required to turn on the camera after clicking once).
Draw: Used to scale the reference bar, drag to create a bar, drag the red dot to adjust the position, and drag the blue line to move it.
Clear: Delete the bar
Refresh: Refresh the camera video connection
Guide Line Color: Change the color of the guidelines displayed in Live View
Rotate: Click the "Rotate" button to rotate the video 180º, and you can create a rotated video without any calibration data.
Live View Setting(Comparison Mode)
Live View Setting (Comparison Mode) allows you to set camera properties, gimbal position, and connect / disconnect the camera to compare two cameras and make detailed settings.
Comparison Mode: Compare the video of two CAMs and set the properties and gimbal Live View Mode: Compare the video of two CAMs and set the properties and gimbal.
Camera Selection (1), (2) : Use the drop-down to select each camera for comparison.
Refresh : Refresh the camera video connection
Live View Comparison Video: Video to compare with the left Live View target
Live View applied image: Image to which the right Live View Property and Gimbal setting values are applied.
Scope comparison: Check the scope status of the image color under the Live View image
Property
Property allows you to set detailed properties of the camera connected to the 4DDM.
Exposure
ISO: Set the light sensitivity number
Aperture: Set the amount of light entering the aperture
Shutter Speed: Set the shutter speed
-/+ 1EV : TBD
Color
White Balance : TBD
Temperature: Setting to adjust the color of light
RGB Balance Adjustment: Set the RGB color of the video
Saturation: Set the color saturation of the image
Contrast: Set the brightness of the image
Hue: Video color settings
Lens
Zoom: Lens zoom setting
Focus: Set lens focus (AUTO: Focus automatically)
Scope
Parade: Video color correction value monitoring mode
Waveform: Waveform monitoring mode for image color correction values
Overlay: Monitoring mode for overlaying image color correction values
Memory / Revert
Memory : Temporarily stores the current Property value and saves it when Save is clicked.
Revert : Return to the property value at the time of clicking Memory
Gimbal
Gimbal allows you to customize the properties of the Gimbal device attached to your camera. These settings are only used when you install and use Gimbal.
Gimbal Control
WakeUp All: Wake up all gimbals
Sleep All: Sleep all gimbals
All: Select all registered gimbal devices to apply option (WakeUp All, Sleep All)
Gimbal Balance
Get Position : Get the current Gimbal position
Set All / Stop All : Roll/Tilt/Pan simultaneously to move/stop coordinates
Speed : Adjust the movement speed of the gimbal
Roll/Tilt/Pan : TBD
Gimbal Controller
[Continuous], [OneStep]: Option to select whether to move the gimbal continuously or in a single step using the buttons.
[Step]: When using the OneStep Gimbal movement option, the interval of movement per click.
Roll/Tilt/Pan: After adjusting the coordinates, click the direction display to move to the set coordinates.
Lens
Zoom: Enter directly or adjust the bar to set a value > Save as [Set]
Focus: Enter directly or adjust the bar to set the value > Save as [Set].
Set: Set the selected value
Auto: Set auto focus
Preset
Preset List: List of available presets for saving Gimbal settings, click to set after
Save: Save the current Gimbal settings to the selected Preset List
Load: Load Preset settings from a specific folder (save to 1-8)
Apply to Gimbal : Apply the current Gimbal setting to the clicked Preset
Set : Save the current Gimbal Position to the selected Preset number
Move: Move the selected Preset number Position value
Step of Gimbal Preset Setting
Step 1. Wake up the gimbal WakeUP All
Step 2. Move the gimbal using the gimbal controller
Step 3. Set the zoom and focus of Lens
Step 4. Click the desired Preset_Number and click Save Preset
(If you want to move to the desired Preset_Number setting value, click Move after clicking Preset_Number)
0 Comments